Water-Blocking Tapes
Longitudinal water blocking for power and communications cables, in non-conductive and semiconductive versions
Water-Blocking Tapes
Water-blocking tapes consist of a non-woven polyester backing impregnated with superabsorbent polyacrylate powder. On contact with moisture, the polyacrylate swells quickly to form a gel that blocks longitudinal water progress inside the cable, limiting damage to the entry area and easing fault location and repair. They are supplied in two versions: non-conductive (CDZD), for power and communications cables, and semiconductive (WBSC2S), for medium- and high-voltage cables where the electric field must also be controlled.
The protection mechanism is passive until water ingress occurs: the tape stays dry and flexible during normal cable operation and is activated only when moisture is detected. This distinguishes swellable tapes from metallic barriers, which provide permanent tightness but cannot contain penetration once it has occurred.
The first decision is the version. CDZD, non-conductive and single-sided, covers communications cables and low- and medium-voltage power cables with no electrical requirement on the tape. WBSC2S, double-sided semiconductive, is used in medium-, high- and extra-high-voltage cables, where electric-field control is as critical as moisture protection; its corrosion inhibitor also protects shield, armouring and conductor in underground or submarine installations.
How to choose the right one?
Once the version is chosen, the reference depends on the balance between blocking capacity, available space and mechanical strength during manufacturing: thicker grades offer greater absorption capacity and swelling speed, while thinner ones suit compact constructions. All WBSC2S references share the same electrical properties; the N series offers higher swelling speed.
Non-conductive — CDZD
| Reference | Thickness | Grammage | Tensile strength | Swell 1 min | Swell 3 min | When to choose |
|---|---|---|---|---|---|---|
| CDZD-10 | 0.10 ±0.01 mm | 40 ±5 g/m² | ≥20 N/cm | ≥3 mm | ≥4 mm | Very tight spaces, compact constructions |
| CDZD-15 | 0.15 ±0.03 mm | 60 ±5 g/m² | ≥25 N/cm | ≥5 mm | ≥8 mm | Communication cables, limited spaces |
| CDZD-18 | 0.18 ±0.03 mm | 65 ±15 g/m² | ≥30 N/cm | ≥6 mm | ≥9 mm | Capacity/space balance |
| CDZD-20 | 0.20 ±0.03 mm | 70 ±10 g/m² | ≥30 N/cm | ≥10 mm | ≥12 mm | LV/MV power cables |
| CDZD-25 | 0.25 ±0.03 mm | 80 ±10 g/m² | ≥35 N/cm | ≥10 mm | ≥14 mm | High absorption capacity |
| CDZD-30 | 0.30 ±0.03 mm | 90 ±10 g/m² | ≥35 N/cm | ≥12 mm | ≥16 mm | Maximum protection, HV cables |
Semiconductive WBSC2S — standard series
| Reference | Thickness | Grammage | Tensile strength | Swell 1 min | Swell 3 min | When to choose |
|---|---|---|---|---|---|---|
| WBSC2S-30 | 0.30 ±0.03 mm | 110 ±10 g/m² | ≥30 N/cm | ≥8 mm | ≥12 mm | MV cables, standard constructions |
| WBSC2S-35 | 0.35 ±0.03 mm | 120 ±10 g/m² | ≥35 N/cm | ≥9 mm | ≥13 mm | Capacity/space balance |
| WBSC2S-40 | 0.40 ±0.03 mm | 130 ±10 g/m² | ≥40 N/cm | ≥10 mm | ≥14 mm | HV cables, greater protection |
| WBSC2S-50 | 0.50 ±0.03 mm | 160 ±10 g/m² | ≥50 N/cm | ≥12 mm | ≥16 mm | Maximum capacity, EHV cables |
Semiconductive WBSC2S — N series (higher swelling speed)
| Reference | Thickness | Grammage | Tensile strength | Swell 1 min | Swell 3 min | When to choose |
|---|---|---|---|---|---|---|
| WBSC2S-25 | 0.25 ±0.03 mm | 110 ±10 g/m² | ≥25 N/cm | ≥7 mm | ≥10 mm | Tight spaces, rapid response |
| WBSC2S-35N | 0.35 ±0.03 mm | 120 ±10 g/m² | ≥35 N/cm | ≥12 mm | ≥15 mm | High swelling speed |
| WBSC2S-40N | 0.40 ±0.03 mm | 140 ±10 g/m² | ≥40 N/cm | ≥12 mm | ≥16 mm | Maximum response, critical cables |
| WBSC2S-50N | 0.50 ±0.03 mm | 170 ±10 g/m² | ≥50 N/cm | ≥13 mm | ≥18 mm | Maximum protection and speed |
Technical specifications
The values shown below come from tests run to international standards and characterise the material's behaviour both during processing and in service.
Non-conductive CDZD — thin grades (CDZD-10 to CDZD-18)
| Property | Test method | CDZD-10 | CDZD-15 | CDZD-18 |
|---|---|---|---|---|
| Thickness (mm) | ISO 9073-2 | 0.10 ±0.01 | 0.15 ±0.03 | 0.18 ±0.03 |
| Grammage (g/m²) | ISO 9073-1 | 40 ±5 | 60 ±5 | 65 ±15 |
| Tensile strength (N/cm, min.) | ISO 9073-3 | ≥20 | ≥25 | ≥30 |
| Elongation (%, min.) | ISO 9073-3 | ≥12 | ≥12 | ≥12 |
| Swell rate 1 min (mm) | GB 450 | ≥3 | ≥5 | ≥6 |
| Swell rate 3 min (mm) | GB 450 | ≥4 | ≥8 | ≥9 |
Non-conductive CDZD — medium/high thickness (CDZD-20 to CDZD-30)
| Property | Test method | CDZD-20 | CDZD-25 | CDZD-30 |
|---|---|---|---|---|
| Thickness (mm) | ISO 9073-2 | 0.20 ±0.03 | 0.25 ±0.03 | 0.30 ±0.03 |
| Grammage (g/m²) | ISO 9073-1 | 70 ±10 | 80 ±10 | 90 ±10 |
| Tensile strength (N/cm, min.) | ISO 9073-3 | ≥30 | ≥35 | ≥35 |
| Elongation (%, min.) | ISO 9073-3 | ≥12 | ≥12 | ≥12 |
| Swell rate 1 min (mm) | GB 450 | ≥10 | ≥10 | ≥12 |
| Swell rate 3 min (mm) | GB 450 | ≥12 | ≥14 | ≥16 |
Semiconductive WBSC2S — standard series (WBSC2S-30 to WBSC2S-50)
| Property | Test method | WBSC2S-30 | WBSC2S-35 | WBSC2S-40 | WBSC2S-50 |
|---|---|---|---|---|---|
| Thickness (mm) | ISO 9073-2 | 0.30 ±0.03 | 0.35 ±0.03 | 0.40 ±0.03 | 0.50 ±0.03 |
| Grammage (g/m²) | ISO 9073-1 | 110 ±10 | 120 ±10 | 130 ±10 | 160 ±10 |
| Tensile strength (N/cm, min.) | ISO 9073-3 | ≥30 | ≥35 | ≥40 | ≥50 |
| Elongation (%, min.) | ISO 9073-3 | ≥12 | ≥12 | ≥12 | ≥12 |
| Swell rate 1 min (mm) | GB 450 | ≥8 | ≥9 | ≥10 | ≥12 |
| Swell rate 3 min (mm) | GB 450 | ≥12 | ≥13 | ≥14 | ≥16 |
Semiconductive WBSC2S — N series (WBSC2S-25 to WBSC2S-50N)
| Property | Test method | WBSC2S-25 | WBSC2S-35N | WBSC2S-40N | WBSC2S-50N |
|---|---|---|---|---|---|
| Thickness (mm) | ISO 9073-2 | 0.25 ±0.03 | 0.35 ±0.03 | 0.40 ±0.03 | 0.50 ±0.03 |
| Grammage (g/m²) | ISO 9073-1 | 110 ±10 | 120 ±10 | 140 ±10 | 170 ±10 |
| Tensile strength (N/cm, min.) | ISO 9073-3 | ≥25 | ≥35 | ≥40 | ≥50 |
| Elongation (%, min.) | ISO 9073-3 | ≥12 | ≥12 | ≥12 | ≥12 |
| Swell rate 1 min (mm) | GB 450 | ≥7 | ≥12 | ≥12 | ≥13 |
| Swell rate 3 min (mm) | GB 450 | ≥10 | ≥15 | ≥16 | ≥18 |
Electrical properties (WBSC2S)
| Property | Test method | Value |
|---|---|---|
| Surface resistance | GB 3048 | ≤1500 Ω |
| Volume resistivity | GB 3048 | <10⁶ Ω·cm |
Thermal and environmental properties
| Property | Test method | CDZD | WBSC2S |
|---|---|---|---|
| Short-term thermal stability | Q/TR.J02.031-2000 · Q/TR.J02.01-2000 | 230 °C | 230 °C |
| Long-term thermal stability | IEC 216 | 90 °C | 90 °C |
| Moisture content | ISO 287 | ≤8% | ≤9% |
Construction
| Component | Material |
|---|---|
| Backing | Non-woven polyester (CDZD) · semiconductive non-woven polyester (WBSC2S) |
| Active agent | Superabsorbent polyacrylate powder |
| Additive | Corrosion inhibitor (WBSC2S) |
| Type | Single-side, non-conductive (CDZD) · double-sided, semiconductive (WBSC2S) |
Values shown are typical and do not constitute binding specifications.
Available variants
Versions
- Non-conductive CDZD — single-side; communications and LV/MV power cables
- Semiconductive WBSC2S — double-sided with corrosion inhibitor; MV, HV and EHV cables with partial-discharge control
Semiconductive series (WBSC2S)
- Standard series — balance between mechanical properties and swelling capacity
- N series — higher swelling speed for critical applications
- Special configurations on request
Delivery formats
The supply format directly influences process continuity and taping efficiency. Material can be supplied in different formats and dimensions adapted to each machine type and production speed.
- OD
- Outer diameter
- ID
- Core inner diameter
- Core
- Plastic or cardboard core
Pad / Roll (pancake)
Pancake format
- A
- Traverse width
- B
- Core length
- C
- Outer diameter (OD)
Spool (TWS / STS reel)
Automatic reel
Other formats and dimensions available on request. Custom slitting service available.
Need technical advice?
Our technical team is available to help you select the optimum material for your application.
Custom slitting
Up to 1200 mm width, ±0.50 mm tolerance
View service
Spooling
Pad to TWS/STS spool conversion
View serviceWe process material from our stock or material supplied by the customer.
Need
technical advice?
Our technical team is available to help you select the optimal material for your application.